CB-Flow Fire Pump Test Trailer

Speed of operation, precise accuracy, ease of operation, cost savings, increased revenues and environmentally enhanced!

Watch the CB-Flow Fire Pump Test video Flowing 2250gpm
Watch video on YouTube
Download a copy of the CB-Flow Brochure/Fact Sheet.

(PHOTO CAPTION TO RIGHT)
The flow unit can be custom built to flow whatever you request. The EzFlow’n Unit pictured above is the 2000 series able to flow up to 3750gpm.

Take a Look at the Unit's Specifications:

Speed of Operation

The CB-Flow unit is completely ready to use the moment you arrive onsite. Just connect the supplied hoses to the buildings test header and begin testing.

Excessive set-up time has been eliminated.
Area of water discharge has been reduced to the bottom of the unit allowing flexibility in testing in tight areas or narrow alleyways.
Having the remote header with all flow device controls at one location allows a single operator to dial in multiple flows rapidly.

Accuracy

The CB-Flow unit with its unique design provides a smooth flow of water, the ability to read flow gages at one remote location and less movement in the gauge, thus resulting in more accurate flow test readings.

The CB-Flow design provides a smoother flow of water resulting in less movement of the test gauge.
Having all flow test gauges at one remote location, you are able to read each gauge independently reducing the overflow or underflow of water.
The CB-Flow unit is designed to use 3-inch fire hoses. The 3-inch fire hoses provide better flow with less friction losses, especially when exceeding 50 feet of hose per nozzle.

Note: The design, quality and accuracy of the gauges are critical when testing fire pumps. A fire pump can pass or fail depending upon the reading of a simple pitot tube. Often the gauge on the tube fluctuates and a “best guess” reading is obtained. The design of the CB-Flow unit minimizes this problem based on using acceptable gages.

The recommended gauges used at the CB-Flow unit must be glycerine filled accurate to 1%. The range of the gauges must not exceed 0 to 60 psi.
The recommended gauges used at the fire pump must be glycerine filled accurate to ½%. The range of the gauges must not exceed 0 to 300 psi.

Note: Water pressure gauges are normally less accurate in the lower and upper 10% of the scale. Using a 0-300 psi gauge is less accurate in the 0 to 30 and 270-300 psi range. With the 60 psi gauges, most readings are taken in the 10-35 psi range where accuracy is at its peak.

(All gauges will require recalibration each year by a certified UL Listed testing laboratory.)

Ease of Operation

The CB-Flow unit is designed for two-person operation, one at the fire pump, and one at the CB-Flow unit. All controls, gauges, valves, etc., are located in one place. The CB-Flow unit has been designed so any one person, who is mechanically-inclined, can operate this unit.

One day of "on-the-job experience" is all the training needed for new operators.
No special qualifications, certifications or training is required to operate the CB-Flow unit.
Operator should be capable of operating a vehicle with a trailer attached, able to read and record pressure gauge readings, as well as handle a 3-inch diameter rubber-lined hose.

Cost Savings and Increased Revenues

The CB-Flow unit has been designed not only to provide accurate testing results, it also allows you to schedule more fire pump testing in a single day.

The CB-Flow unit requires two people to run a complete test. A third person is no longer needed.
The person operating the CB-Flow unit does not have to be experienced in fire pump testing. They only should be trained in the proper procedures in operating fire hoses, dialing in, and recording readings. Therefore a low dollar-per-hour helper can perform this test.
The estimated cost savings on eliminating one (1) employee with a total cost of $30 per hour (including tax, insurance, workman compensation, travel time, etc.) is estimated at two hours—saving you $60 per test.
Increasing fire pump testing in a single day (estimated from 3 to 4 tests per day to 6 to 7 tests per day). Based upon charging a customer $850 per test, your gross income could increase by $2,550 per day. Also, being able to schedule more fire pump tests in a single day, your technicians can work on other projects making you additional revenue.

If you have at least 50 fire pump tests scheduled in a single year, this unit could pay for itself in approximately 3 to 5 years. Thus, the more tests you do, the more money you can save and the quicker the CB-Flow unit pays for itself.

Environmentally-Friendly

Uses less water because of the ease of operation and centrality of operations; water is flowing for only about one-quarter of the time. This means:

Significantly less water is wasted.
The job is completed in less time.
The operator is not exposed to water or water spray, increasing the temperature extremes in which the pumps can be tested.
Damage to parking lots, landscaping, etc. is minimized.

Your CB-Flow Standard Unit Includes...

As is shown in picture, the CB-Flow unit includes:

A fixed trailer with 2' 5/16" ball hitch.
Heavy duty axel with steel belted 8‐ply heavy duty tires.
Electric brakes rough in (not required but provided on stock axel).
Hydro flow Pitotless Nozzles 7‐1 ¾ inch and 1‐1 1/8 inch (customer requested nozzle sizes).
Brass 2-½ inch hose valves.
Quick connect gage couplings (both female and male ends).
Pitot tube bleed off ¼ inch brass valves.
Front of trailer hose rack.
Operational training and safety video.

Your "Ready-to-Go" Options Include...

At an additional cost, your unit can include:

Calibrated water gauges. 8 – 0‐60psi 1% accuracy 4-inch face UL Listed glycerin filled
Protective foam gauge case
Electric brake wiring harness (If requested)
Eight lengths of 3-inch diameter 50-foot hose custom made (female x female)
Eight lengths of 3-inch diameter 25-foot hose custom made (female x female)
CB-Flow storage cover (For storage only. Not intended for travel)

Fire Pump Flow Testing in Half the Time of Conventional Methods; Take a Look:

Easy setup, just "Hook up and Flow."
Remote Test Header allows reduction in labor costs.
Accurate results using the FM-approved Pitotless Nozzle.™
No need to get wet while reading water gauges.
Pump tests performed practically "anywhere" including tight alleyways.
Uses one-quarter of the water labeling this unit "GREEN."
Practically maintenance free.
Will pay for itself over a short period of time.

CB-Flow Facts